Genelec 1037A
System Specifications
| Lower cut-off frequency, -3 dB: | < 38 Hz | |
| Upper cut-off frequency, -3 dB: | > 22 kHz | |
| Free field frequency response of system | 39 Hz - 21 kHz (± 2.5 dB) | |
| Maximum short term sine wave acoustic output on axis in half space, averaged from 100 Hz to 3 kHz | @ 1 m > 114 dB SPL | |
| Maximum long term RMS acoustic output in same conditions with IEC-weighted noise (limited by driver unit protection circuit) | @ 1 m > 106 dB SPL | |
| Maximum peak acoustic output per pair on top of console, @ 1.7 m from the engineer with music material | > 125 dB | |
| Self generated noise level in free field @ 1 m on axis | < 15 dB (A weighted) | |
| Harmonic distortion at 95 dB SPL at 1m on axis f < 100 Hz f > 100 Hz |
< 3 % < 0.5 % |
|
| Drivers Bass Mid Treble |
305 mm (12") cone 130 mm (5") cone 25 mm (1") metal dome |
|
| Weight: | 35 kg (77 lb) | |
| Dimensions Width Height Depth |
680 mm (26 3/4") 400 mm (15 3/4") 380 mm (15") |
|
Amplifier |
||
| Bass amplifier output power with a 6 ohm load | Short term 160 W | |
| Midrange amplifier output power with a 4 ohm load | Short term 160 W | |
| Treble amplifier output power with a 8 ohm load | Short term 120 W | |
| Long term output power is limited by driver unit protection circuitry | ||
| Slew rate | 80 V /µs | |
| Amplifier system distortion at nominal output THD SMPTE-IM CCIF-IM DIM100 |
< 0,05 % < 0,05 % < 0,05 % < 0,05 % |
|
| Signal to Noise ratio, referred to full output bass midrange treble |
> 100 dB > 100 dB > 100 dB |
|
| Mains voltage | 100/200 V or 115/230 V | |
| Voltage operation range at 230V setting | 207 - 253 (± 10 %) | |
| Power consumption, idle full output |
50 W 300 W |
|
Crossover |
||
| Input connector: XLR female | pin1 gnd pin 2+ pin 3- |
|
| Input impedance | 10 kOhm | |
| Input level for 100 dB SPL output @1 m | variable from +6 to -6 dBu | |
| Input level for maximum short term output of 114 dB SPL @1 m | variable from +20 to +8 dBu | |
| Subsonic filter below 35 Hz: | 18 dB / octave | |
| Ultrasonic filter above 25 kHz | 12 dB / octave | |
| Crossover frequency bass / mid mid / treble |
420 Hz 3,2 kHz |
|
| Crossover acoustical slopes | 18 - 24 dB / octave | |
| Crossover level control operation range in 1 dB steps bass middle treble |
from 0 dB to -6 dB from 0 dB to -6 dB from 0 dB to -6 dB |
|
| Bass roll-off conrol in 2 dB steps | ||
| Bass tilt control in 2 dB steps: | ||
| The 'CAL' position is with all tone controls set to 'off' and input sensitivity control to maximum. | ||
All data subject to change without prior notice |
||